Author Topic: Feedback for -- V1.0.3 -- 12Sept 2012 XX OPEN BETA XX for MED1000X3D  (Read 23122 times)

Offline TheKillingBean

  • Newbie
  • Posts: 20
  • Helpful Contribution Status: +0/-0
Re: Re: Feedback for -- V1.0.3 -- 12Sept 2012 XX OPEN BETA XX for MED1000X3D
« Reply #30 on: September 16, 2012, 07:49:50 PM »
Have you tried turning on autofps?

Verstuurd van mijn GT-I9300 met Tapatalk

Yes I tried autofps on, but the same thing happens. Nobody else have this problem? I think is easy to check. Just watch a movie, press the settings button. Then you can see if the settings is on HDMI Auto or not.

Offline couto

  • B8a Tester - 1000X3D
  • Hero Member
  • ****
  • Posts: 853
  • Helpful Contribution Status: +7/-2
Re: Re: Feedback for -- V1.0.3 -- 12Sept 2012 XX OPEN BETA XX for MED1000X3D
« Reply #31 on: September 16, 2012, 11:31:06 PM »
Yes I tried autofps on, but the same thing happens. Nobody else have this problem? I think is easy to check. Just watch a movie, press the settings button. Then you can see if the settings is on HDMI Auto or not.

whats settings you got in your tv ?
what time off file you try to play?

try to reflash the firmware using the power button way (15seconds)
Med1000X3D
Anthem MRX-310
Mitsubishi HC5
LG Oled 1080P
100 inch screen
Video setting: 23,976Hz On, auto frame ON
Media Source: Wired Network > ds412+ synology
Router. Linksys E4200
Protocol : UDP 32K
Media Files:ISO 3D, MKV, FLAC

Offline Maasbommel

  • Global Moder8or
  • M8er Addict
  • *****
  • Posts: 11 503
  • Helpful Contribution Status: +51/-8
Re: Feedback for -- V1.0.3 -- 12Sept 2012 XX OPEN BETA XX for MED1000X3D
« Reply #32 on: September 17, 2012, 06:46:31 AM »
Yes I tried autofps on, but the same thing happens. Nobody else have this problem? I think is easy to check. Just watch a movie, press the settings button. Then you can see if the settings is on HDMI Auto or not.

Can you post some more details about your setup:
1] what brand and type of TV are you using?
2] how is your Mede8er connected? Direct to HDMI/by some splitter/by an audio amp: if yes-which brand and type?
3] streaming from internal disk and or network?
4] if network, streaming over samba filesharing/NFS or Upnp?
Read the  Mede8er 400X/500X Beginners Guide
or Mede8er 500X2/400X2/450X2 Beginners Guide

Also check the Couto X3D Newbies Guide first.

Please don't PM me but post on the forum.

Offline TheKillingBean

  • Newbie
  • Posts: 20
  • Helpful Contribution Status: +0/-0
Re: Feedback for -- V1.0.3 -- 12Sept 2012 XX OPEN BETA XX for MED1000X3D
« Reply #33 on: September 17, 2012, 08:42:07 AM »
1] what brand and type of TV are you using?
LG 42SL8500
2] how is your Mede8er connected? Direct to HDMI/by some splitter/by an audio amp: if yes-which brand and type?
Mede8er trough my Onkyo 609, but also happens if connected to the TV directly.
3] streaming from internal disk and or network?
Streaming from internal disk (SEAGATE BARRACUDA 2 TB 7200 RPM 64 MB 3,5 INCH)

Offline hdmkv

  • B8a Tester - 1000X3D
  • Experienced Member
  • ****
  • Posts: 205
  • Helpful Contribution Status: +0/-1
Re: Feedback for -- V1.0.3 -- 12Sept 2012 XX OPEN BETA XX for MED1000X3D
« Reply #34 on: September 17, 2012, 11:57:13 AM »
Experiencing my first stutter with the 1000X3D. It's with the new 'Titanic' 3D BD over wired SMB. Starts around chapter 5, with video stuttering, followed by audio dropouts, and even playback itself freezing. Seems like a network issue. I haven't tried the title via direct USB connection yet. I also played the latest 'Transformers' 3D ISO for about 30 minutes via SMB without issues. Can someone with 'Titanic' 3D do a playback test over network? Thanks.
(2x) MED600X3D (HDMI Auto, auto frame rate, RAW 7.1 audio)
Firmware: Always Latest Beta
Networked via CAT5e
Streaming from Synology DS1812+ NAS via NFS
BenQ W1070 projector with 133" 16x9 Da-lite High Power screen
Audio connection via HDMI to Denon AVR-1913 receiver
Audio output to Pioneer SP 'Andrew Jones' 7.1 speaker system
Also networked: HTPC's, Fire TV's, Roku, PS3

Offline Mede8er1

  • Administr8or
  • Hero Member
  • ******
  • Posts: 3 770
  • Helpful Contribution Status: +113/-28
Re: Feedback for -- V1.0.3 -- 12Sept 2012 XX OPEN BETA XX for MED1000X3D
« Reply #35 on: September 17, 2012, 12:44:19 PM »
hdmkv

Are you using Samba or NFS? As we know NFS bandwidth on X3 is over 25% better than Samba but you need to confirm that your Synology NFS is set to the correct block size. --  ie rsize / wsize should be set to 32768 Bytes otherwise performance will be no better than Samba

Mede8er1

Mede8er1
The Greatest Show on Earth
Read the user Guides
http://www.mede8er.com/mede8er_support_user_guides.htm

Offline hdmkv

  • B8a Tester - 1000X3D
  • Experienced Member
  • ****
  • Posts: 205
  • Helpful Contribution Status: +0/-1
Re: Feedback for -- V1.0.3 -- 12Sept 2012 XX OPEN BETA XX for MED1000X3D
« Reply #36 on: September 17, 2012, 02:40:58 PM »
Samba. Had tried to get NFS working a while back, but was unsuccessful. Will retry NFS, but if not, will re-test 'Titanic' 3D via an attached USB.
« Last Edit: September 17, 2012, 02:59:41 PM by hdmkv »
(2x) MED600X3D (HDMI Auto, auto frame rate, RAW 7.1 audio)
Firmware: Always Latest Beta
Networked via CAT5e
Streaming from Synology DS1812+ NAS via NFS
BenQ W1070 projector with 133" 16x9 Da-lite High Power screen
Audio connection via HDMI to Denon AVR-1913 receiver
Audio output to Pioneer SP 'Andrew Jones' 7.1 speaker system
Also networked: HTPC's, Fire TV's, Roku, PS3

Offline hdmkv

  • B8a Tester - 1000X3D
  • Experienced Member
  • ****
  • Posts: 205
  • Helpful Contribution Status: +0/-1
Re: Feedback for -- V1.0.3 -- 12Sept 2012 XX OPEN BETA XX for MED1000X3D
« Reply #37 on: September 17, 2012, 03:37:32 PM »
Not sure who (Maasbommel or Mede8er1 I think) recently posted instructions on setting up NFS with Synology for 1000X3D. Did a search and couldn't find it. Would you kindly post a link to it? Thanks.
(2x) MED600X3D (HDMI Auto, auto frame rate, RAW 7.1 audio)
Firmware: Always Latest Beta
Networked via CAT5e
Streaming from Synology DS1812+ NAS via NFS
BenQ W1070 projector with 133" 16x9 Da-lite High Power screen
Audio connection via HDMI to Denon AVR-1913 receiver
Audio output to Pioneer SP 'Andrew Jones' 7.1 speaker system
Also networked: HTPC's, Fire TV's, Roku, PS3

Offline Mede8er1

  • Administr8or
  • Hero Member
  • ******
  • Posts: 3 770
  • Helpful Contribution Status: +113/-28
Re: Feedback for -- V1.0.3 -- 12Sept 2012 XX OPEN BETA XX for MED1000X3D
« Reply #38 on: September 17, 2012, 04:28:55 PM »
hdmkv

I found this but its a different model to yours - maybe worth a read anyway

http://www.mede8erforum.com/index.php/topic,1574.0.html

Mede8er1

Mede8er1
The Greatest Show on Earth
Read the user Guides
http://www.mede8er.com/mede8er_support_user_guides.htm

Offline hdmkv

  • B8a Tester - 1000X3D
  • Experienced Member
  • ****
  • Posts: 205
  • Helpful Contribution Status: +0/-1
Re: Feedback for -- V1.0.3 -- 12Sept 2012 XX OPEN BETA XX for MED1000X3D
« Reply #39 on: September 17, 2012, 04:29:56 PM »
Thanks, will try it.
(2x) MED600X3D (HDMI Auto, auto frame rate, RAW 7.1 audio)
Firmware: Always Latest Beta
Networked via CAT5e
Streaming from Synology DS1812+ NAS via NFS
BenQ W1070 projector with 133" 16x9 Da-lite High Power screen
Audio connection via HDMI to Denon AVR-1913 receiver
Audio output to Pioneer SP 'Andrew Jones' 7.1 speaker system
Also networked: HTPC's, Fire TV's, Roku, PS3

Offline Maasbommel

  • Global Moder8or
  • M8er Addict
  • *****
  • Posts: 11 503
  • Helpful Contribution Status: +51/-8
Re: Re: Re: Feedback for -- V1.0.3 -- 12Sept 2012 XX OPEN BETA XX for MED1000X3D
« Reply #40 on: September 17, 2012, 06:27:41 PM »
hdmkv

I found this but its a different model to yours - maybe worth a read anyway

http://www.mede8erforum.com/index.php/topic,1574.0.html

Mede8er1

Exactlly the same for the 1000x3d.
Also verify if your synology is not on jumbo frames for first setup of nfs.
And try first to connect using your synology admin account  - later when it works you can fall back to separate user accounts. First try setting up simple like this.

Verstuurd van mijn GT-I9300 met Tapatalk
Read the  Mede8er 400X/500X Beginners Guide
or Mede8er 500X2/400X2/450X2 Beginners Guide

Also check the Couto X3D Newbies Guide first.

Please don't PM me but post on the forum.

Offline Mede8er1

  • Administr8or
  • Hero Member
  • ******
  • Posts: 3 770
  • Helpful Contribution Status: +113/-28
Re: Feedback for -- V1.0.3 -- 12Sept 2012 XX OPEN BETA XX for MED1000X3D
« Reply #41 on: September 18, 2012, 10:56:59 AM »
Locked - New Release

Mede9er1

Mede8er1
The Greatest Show on Earth
Read the user Guides
http://www.mede8er.com/mede8er_support_user_guides.htm